How To Restore A Weathered Deck: Seal Your Deck Cracked Wood Quickly

We always love to sit on a nice deck and spend great pastimes with our friends and family. How important a deck is for us, we know that. It’s usually that we don’t take good care of it, that causes lots of trouble.

Sometimes homeowners notice that their deck is getting old while they have a new house. They sit helplessly, thinking replacement is the only option. Later, they discover that an abandoned deck can be revived by taking the right approach. If you’re embarrassed with the look of your shabby old deck, there’s usually an option for refurbishing it.

Depending on the worn woods, you’ve to decide which protective seal (stain or paint) will work for your weathered deck.

We have some great tips on how to restore a weathered deck. If you don’t get ideas to deal with your damaged, twisted nail pops and fade away deck, follow the techniques we showed and get back your deck before the summer.

Complete Instructions On How To Restore A Weathered Deck

If your deck doesn’t look good, that means the boards are splintered and have faded away to a dingy shade of gray. You can find some boards that are actually twisted, and nails are popping up all over. This is pretty bad, and we are fairly confident the revival is possible.

It is possible to reduce costs by working on your own rather than looking for a professional. Read the guidelines below prior to restoring your weathered deck by yourself.

Prepare The Deck

The surface of the deck boards could be cracked and twisted. Water soaking, continual movement expansion, and contraction cause all of those problems. The way to prevent it is to make sure you put a good sealer on your deck every 1 or 2 years.

Replace all damaged and rotted boards with new boards. Screw them in the nearest joists. Also, inspect the handrails and balusters, repair or replace the damaged section.

Now for the last time, check the railings and boards. If you find any loose paint or finish, remove them using a scraper tool. If your deck has large splinters, sand them with sandpaper. Use the sanding tool instead of using your hand to make the job easier.

Cover Everything Around

Once you have done all the preparation, move forward and cover everything around the deck. Tape plastic sheet over nearby house siding, plants and beneath the deck to prevent splash of paint or stain. Don’t forget to cover the railing and balusters if you aren’t refinishing them.

Clean Previously Unfinished Deck

Wear necessary protective gear (glass, mask, hand gloves, and boots) before starting cleaning. If your deck isn’t unfinished previously, a DIY cleaning will be enough for removing mildew and dirt.

Take a 5-gallon plastic bucket and fill it with 3 quarts of warm water, 1 quart of bleach, and ⅓ cup of powder laundry detergent. Mix those ingredients thoroughly and apply them to the deck. Scrub the area with a brush from different angles and rinse through a hose or power washer.

Strip Previously Finished Deck

If you want to work on a previously finished deck:

  • Strip it first before going into details.
  • Take your required deck stripper and apply it with a pump sprayer. You must wear protective gear.
  • Apply separately on both deck boards and handrails.
  • Wait 15 minutes to sit the stripper, then scrub with a push brush or bristle brush.
  • Watch your footsteps so you don’t slip.

Rinse The Deck

A pressure washer is the most smooth way to rinse your deck. If you use it, set the pressure 1500 to 2500 PSI. Set the tip at a distance of 6 inches from the wood surface. But, if you feel worried the pressure washer can damage your deck, use a brush to scrub the entire deck.

Sanding The Deck

A smooth surface is required if you want to achieve a long-lasting application for your deck. Use a sanding pole and 60 or 50 grit sandpaper for sanding the entire deck surface. Also, sand the handrail and balusters using your hand or electric sander. Swap with a brush or vacuum all dust and debris.

Seal The Deck

If you are looking stain or paint for older deck, a semi-transparent stain works best. But, before staining your deck, ensure the weather is clean and shiny because stains take time to set in deck wood. You can use a roller or synthetic brush to stain the entire deck. Some variant colors can be used with a thin coat. But don’t apply too much stain that would be tough to remove in the future. Also, make sure you cover all the surfaces and fill the cracks.

When you apply a stain, you must have to apply a sealer over the stain. Otherwise, colors will not stay too long on the deck board. Some stains come together with the sealant, and a few aren’t. Read the manufacturer guide properly to know whether the sealant is included or not.

Final Words

Do you have a weather deck? The overall guideline on how to restore a weathered deck is very clear and straightforward. It’s very understandable for both newbies and pros. If you really have a hard time with your weather deck, you’ll love to restore the deck from today. When you are done with all the restoration, you will fall in love and sit relaxed on the deck.

So, what next! Stay updated with us for home DIY tips and hacks.

Leave a Comment